Sungold Abrasives 30516 Aluminiumoxid, Körnung 80, Rollen für Trommelschleifer, 3 breit x 35 Fuß

Brand:Sungold Abrasives

3.2/5

70.78

Das Befestigen von Muttern an einer Gewindestange kann aufgrund des begrenzten Platzes und der Hindernisse um die Stange herum schwierig sein. Die seitliche Bewegung ist begrenzt. Bei langen Abschnitten der Gewindestange greifen herkömmliche Steckschlüssel nach unten, so dass Sie die Mutter nur bis zu einem bestimmten Punkt an der Stange nach oben schieben können. Kleins Hochleistungs-Steckschlüssel verfügen über einen durchgehenden Griff und einen vollständig hohlen Schaft, der das Eindrehen von Schrauben auf unbegrenzte Schraubenlängen ermöglicht. Die Schraubenschlüsselunterstützung sorgt für ein höheres Drehmoment, während die magnetischen Spitzen jede Mutter richtig greifen.

Kann für jede Anwendung verwendet werden, bei der ein Zuschnitt auf die richtige Größe erforderlich ist. Verwenden Sie den Streifen an der Maschine als Schablone zum Schneiden des neuen Streifens. Kann 4 Streifen für eine 16-Trommel wie den Jet16-32 herstellen. Premium-Aluminiumoxide mit X-Gewicht schneiden schnell und halten den anspruchsvollsten Schleifanwendungen stand. Zur Verwendung mit Trommelschleifern, um Geld zu sparen, indem Sie Ihre Streifen selbst schneiden.
Backing Type Paper
Backing Type ‎Paper
Batteries Required? ‎No
Brand Sungold Abrasives
Brand ‎Sungold Abrasives
Color Gold
Color ‎Gold
Compatible Material ‎Wood, Metal, Stone
Customer Reviews 4.2 4.2 out of 5 stars 175 ratings 4.2 out of 5 stars
Grit Number ‎80
Grit Type ‎Medium
Included Components ‎Abrasives Roll
Item model number ‎30516
Item Package Quantity ‎1
Item Weight ‎0.01 ounces
Manufacturer ‎Sungold Abrasives
Material ‎Aluminum Oxide
Package Dimensions ‎6.73 x 6.54 x 3.54 inches
Part Number ‎30516
Product Dimensions 420"L x 3"W
Product Dimensions ‎420"L x 3"W
Size 80 Grit
Size ‎80 Grit
Unit Count ‎35.0 Foot

3.2

8 Review
5 Star
60
4 Star
21
3 Star
7
2 Star
2
1 Star
10

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: Richard
Great for a drum sander
Drum sanders exist in a somewhat obscure niche of woodworking - higher end than a lot of home shops have use/space for and to low end for a pro shop that would otherwise use a wide belt sander. Not to mention that there are few definitive sources for how to cut a proper angle/taper on an abrasive so it properly fits a drum sander. So lots of folks who own drum sanders stick with buying overpriced products with pre-cut tapers and pre-determined lengths specified for their model of drum sander. Once you figure out the math and technique, however, the world is yours for buying abrasives in bulk at much lower cost than the manufacturer of your drum sander and its distributors would sell them for because you can buy any width you want, allowing you to prioritize price rather than being dependent on using an exist wrap as a template. That is where getting the math right is crucial because I purchased this thinking it would give me 4 wraps for my 18-36 Delta 31-250 drum sander, but I was wrong and I can only get 3 with a ton left over (but not enough for a 4th wrap). That is not a knock on this product, because it was entirely my fault. Given my experience I would trust the product description that says you could get 4 wraps for a 16-32 drum sander, but I cannot verify it. So here is the math for determining the length you will need for a single wrap of your drum sander drum: ((Circumference of the drum * length of drum) / width of abrasive) + circumference of the drum In my case that works out to being 110.25 inches per wrap. So I needed to buy one step up from this (38 feet) to get 4 wraps, but again, that is entirely my fault. I’ll leave it to you to go find a video or write up about how to cut the tapers properly, but I don’t trust the formulas used by most places since everything I read forgot to add the last “circumference of the drum” and therefore bought the wrong product.
Scritto da: robert d.
Roll was short ~ 1 foot.
Roll was short ~ 1 foot which limited number of segment lengths achievable for drum sander thus wasting paper and value.
Scritto da: Customer Review
Very aggressive
Installed on grizzly drum sander and so far I’m pleased by the amount of wood it takes off
Scritto da: Amazon Customer
Easy to work.
I used this on my 18” finish sander from Grizzly. Holds up well does not clog up like cheap sandpaper.
Scritto da: Frank Switalski
Not durable at all.
Upon second use paper ripped on relatively small passes. Would be a one if not for the price.
Scritto da: M Krebs
good sandpaper
Bought this for my Jet drum sander to save money. Turns out it's also vastly superior to the precut junk that Jet sells. Cuts well, doesn't clog up so bad.
Scritto da: dmann
Works for my Preformax drum sander
The price is good and quality is fine. I will be buying more as needed.
Scritto da: Dwayne Brown
Not very durable.
Doesn't last as long as other brands I've used.

Verwandte Produkte

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array