KRAUS Standart PRO 25-Zoll-Drop-In-Top-Mount-16-Gauge-Edelstahl-Einzelbecken-Waschbecken, KHT301-25L 25-Zoll-Wäschebecken mit engem Radius

Name: KRAUS Standart PRO 25-Zoll-Drop-In-Top-Mount-16-Gauge-Edelstahl-Einzelbecken-Waschbecken, KHT301-25L 25-Zoll-Wäschebecken mit engem Radius
Brand: Kraus
SKU: 0846639062855
Price: 1048.85 EUR
Availability: InStock

Brand:Kraus

3.7/5

€
1048.85

Mit einem eleganten, modernen Design mit geraden Wänden und leicht zu reinigenden abgerundeten Ecken sorgt das robuste, extra tiefe Standart PRO-Waschbecken für einen wunderbar modernen Look in Ihrer Küche, Bar, Waschküche, Schlammküche oder Werkstatt. Hergestellt aus dem proprietären KRAUS TRU16 – einem robusten, echten 16-Gauge-Edelstahl – bietet dieses Arbeitstier einer Spüle eine überragende Haltbarkeit und Widerstandsfähigkeit gegen Dellen und Beschädigungen. Mit einer extra tiefen Beckentiefe von 11 3/8 Zoll bewältigt dieses vielseitige Spülbecken die schwierigsten Aufgaben, darunter das Waschen übergroßer Gegenstände und das Einweichen großer Wäscheladungen. Ausgestattet mit der überlegenen NoiseDefend-Schalldämpfungstechnologie und Super-Silencer-Pads, um Geräusche und Vibrationen zu eliminieren, wenn die Spüle in Betrieb ist. Eine ungiftige Grundierung isoliert die Spüle, sodass das Wasser seine Temperatur behält und Kondensation verhindert, die den Unterschrank beschädigen könnte. Die verschleißfeste Oberfläche ist ideal für Spülen, die häufig genutzt werden, ist extrem langlebig und rostet nicht oder wird mit der Zeit stumpf. Die nach hinten versetzte Ablauföffnung und der geneigte Boden mit Kanalrillen sind für ein schnelles und vollständiges Abfließen konzipiert und verhindern, dass sich Wasser in der Spüle ansammelt. Dadurch wird sichergestellt, dass die Wäsche besser abfließt als bei herkömmlichen Wäschespülen mit flachem Boden. Das praktische Drop-In-Design kann mit jeder Art von Arbeitsplatte für einen schnellen Küchenumbau installiert werden, mit einer extra dicken 4-mm-Deckplatte, die flach auf der Arbeitsplatte aufliegt und für ein perfekt vollendetes Erscheinungsbild sorgt. Diese Spüle verfügt über ein schützendes Bodengitter aus Edelstahl und eine hochwertige Ablaufgarnitur mit abnehmbarer dekorativer Ablaufabdeckung, die für ein sauberes und nahtloses Erscheinungsbild sorgt. Genießen Sie den Vorteil von High-End-Qualität und modernem Stil über die Küche hinaus mit der Standard-PRO-Spüle.

Menge

in den Warenkorb legen Kaufe jetzt

EAN: 0846639062855

Kategorien Werkzeuge & Heimwerken, Küchen- & Badarmaturen, Küchenarmaturen, Küchen- & Barspülen, Küchenspülen, Einzelschüssel,

ENTHÄLT SCHUTZBODENGITTER: Edelstahl-Spülgitter verhindert Kratzer und ermöglicht ein einfaches Abfließen des Wassers – PREMIUM-ABFLUSSBAUGRUPPE mit herausnehmbarem Sieb fängt Abfall auf, um das Abflussrohr frei zu halten – DEKORATIVE ABFLUSSABDECKUNG verbirgt die Abflussöffnung, um dieses Spülbecken noch stilvoller zu machen. PERFEKTER ENTWÄSSERUNG: Die nach hinten versetzte Ablauföffnung und der sanft geneigte Boden mit Kanalrillen verhindern, dass sich Wasser im Spülbecken ansammelt – LÄSST BESSER ab als herkömmliche Wäschespülen mit flachem Boden! – SCHÜTZENDE UNTERBESCHICHTUNG sorgt für eine hervorragende Wärmedämmung und verhindert Kondenswasserbildung, die den Unterschrank beschädigen kann. Robuster 16-Gauge-Stahl: Hergestellt aus proprietärem KRAUS TRU16 – einem extra dicken echten 16-Gauge-Edelstahl – für überragende Haltbarkeit und Widerstandsfähigkeit gegen Dellen und Beschädigungen; VERSCHLEISSFESTES GEWERBLICHES FINISH rostet nicht und wird durch den täglichen Gebrauch nicht stumpf, ist leicht zu reinigen – ÜBERLEGENE SCHALLDÄMPFUNG: Die extrem leise NoiseDefend-Technologie mit extra dicken Super-Schalldämpferpolstern eliminiert Lärm und Vibrationen. EXTRA-TIEFES WASCHBECKEN eignet sich ideal für den Einsatz in Waschküchen, Toiletten und Hauswirtschaftsräumen – das Spülenset enthält VIELE EXTRAS, darunter ein schützendes Bodengitter, eine Premium-Ablaufgarnitur, eine dekorative Ablaufkappe und ALLE MONTAGEHARDWARE – ABMESSUNGEN DES AUSSENSPÜLENS: 25 Zoll . L x 22 Zoll B x 11 3/4 Zoll T; INNENABMESSUNGEN: 23 Zoll L x 18 Zoll B x 11 3/8 Zoll T; Mindestschrankgröße: 27 Zoll.

Assembly Required	‎Yes
Batteries Required?	‎No
Brand	Kraus
Brand	‎Kraus
Color	Tight Radius
Color	‎Tight Radius
Customer Reviews	4.7 4.7 out of 5 stars 826 ratings 4.7 out of 5 stars
Drain Type	‎Grid
Finish	‎Stainless Steel
Finish Type	‎Stainless Steel
Included Components	‎Sink, bottom grid, premium drain assembly, decorative drain cap, Mountning Hardware
Installation Method	‎Drop-in
Item model number	‎KHT301-25L
Item Package Quantity	‎1
Item Weight	‎26.9 pounds
Item Weight	‎26.92 Pounds
Manufacturer	‎Kraus
Material	Stainless Steel
Material	‎Stainless Steel
Part Number	‎KHT301-25L
Product Care Instructions	‎Laundry
Product Dimensions	22"D x 25"W x 11.38"H
Product Dimensions	‎22 x 25 x 11.38 inches
Product Dimensions	‎22"D x 25"W x 11.38"H
Shape	‎Rectangular
Size	25 Inch
Size	‎25 Inch
Style	‎Laundry Sink
Warranty Description	‎Limited Lifetime Warranty

5 Star

4 Star

3 Star

2 Star

1 Star

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet^*

Deine Bewertung

Scritto da: Animation Fan

Beautiful sink, with design flaws (that can be overcome)

As the last of the attached photos shows, the sink is beautiful installed. I really like the contrast of stainless steel with the copper-clad countertop, and it's such a modern, sleek look. Cannot speak yet to durability or maintainability, but so far I love it. It's a good thing I am handy, because it had two basic problems I had to overcome. The first, as shown in the second photo (they are not in ideal order), is that the edge that rests on the counter is just the thickness of the sheet stainless steel. The instructions indicated to simply bed this down in caulk, but I did not think this would make a good, long-lasting seal. The bottom along the edge needed to present a broader surface for the caulk to interact with. As shown in the first photo, I achieved this by glueing 1/4" brass rod along the perimeter. I used JB Weld epoxy. When installed this provided plenty of purchase for the caulk, along with stiffening the edges. I could have used wood but I wanted maximum water resistance in case the caulk ever failed anywhere. I expect the same could be achieved, more cheaply, with autobody filler carefully leveled off. The second problem is the clips provided to secure the sink to the countertop from underneath. They look ingenious and elegant, but, unless you have easy access to the sink from underneath (very unlikely in an existing countertop - possibly if attaching the sink to the countertop before attaching the countertop to the cabinet) - they are virtually unusable. The reason is that the springy part that gets drawn up against the underside of the countertop sticks out far enough that, if they are installed on the sink prior to dropping it into the cutout, it can't fit, as I discovered when I tried it. If the cutout were enlarged sufficiently to avoid this, I suspect the sink would just fall through the cutout, or at least be dangerously close to doing so. If you had plenty of room on all sides you might be able to attach the clips from underneath after dropping the sink in; luckily, this proved unnecessary. I'd advise against using the clips anyway as I doubt you could ever get them off again to remove the sink if you needed to. The good news is, at least given my brass rod alteration, caulk alone is more than sufficient for a very strong bond between sink edges and countertop. I threw the clips in the metal recycling. The caulk I used was GE Silicone Metal, in stainless steel color. Makes for a beautiful, strong yet almost invisible finishing touch that I expect to last a long time, without water infiltration. Time of course will tell. Be sure to use carefully-aligned masking tape on both countertop and sink edge before caulking, for a first-class result. I used the drain fitting it came with though dubiously, as except for the top as seen in the sink, it is made of plastic. Remains to be seen how it holds up, especially to boiling pasta water poured down the drain. It did make a perfect, non-leaking seal on the first attempt (no plumbers putty), which is more than I can say with any prior drain I've installed - the type that does use plumbers putty. It has an unusual way of working - rather than tightening a large nut the circumference of the drain from underneath, the top and bottom halves are connected via a bolt that extends from the bottom piece upwards, to which is screwed a fitting in the center of the drain from the top. Seems to work quite well - the only issue is that the slot the fitting has, intended to get a purchase on it when tightening, has a hole in the middle, and the two ends are too far apart to use even a very large screwdriver. I used an old 1" chisel as a screwdriver, which worked great. I figure if the drain does not hold up it will be easy to remove and replace, so I took a chance on it. If it weren't for these issues it would be five stars. The faucet, of course, is not included with the sink.

Scritto da: Greg

Everything and a kitchen sink!

I love this sink! The only complaint I have is it was a little difficult to figure out the conversion of a two drain sink to a one drain sink. The hole is still in the same location just couldn’t figure out piping without some help. I will add a picture which may help others with the conversion.

Scritto da: KB

Quality and solid workmanship!

I love this sink!! We bought it for our laundry room and honestly I would never thought I would fall in love with a stainless steel sink but it is beautiful!! As you can see, we aren’t quite done with the details yet, but we are already using it. Cleans easily. The depth is perfect!

Scritto da: Nanci

Great Sink

Replaced Old Sink To This One And Its Absolutely Beautiful I Love It

Scritto da: JES

Love my sink

I’ve had this sink for several years and I am really thankful for it. It is easy to clean, but do not use anything abrasive on it or you will have scratch marks. This one came with a grate which also helps protect the bottom against scratches. (P.S. It makes a great place for bathing babies so you don’t have to bend over the edge of a bathtub!)

Scritto da: David

Beautiful!

This sink is so spacious and gorgeous. I have the same complaint as other reviews I saw though and bought it knowing that this may happen to me - the sink must be cleaned every time you use it because of water marks which are annoying and make it look dirty. You also should use the grate to protect the bottom of the sink from scratches. The other complaint I have is that although there are angled parts of the bottom of the sink to help water drain, it doesn’t work. Water droplets sit and pool in the sink and you have to hand dry it when you’re done. If we are going off aesthetics and making good use of space though, this sink is amazing. We have gotten lots of compliments on it!

Scritto da: lisa r robinson

Beautiful

Great sink. This sink is so nice. Looks so nice installed.

Scritto da: Eric Wheeler

Sturdy

This sink is very sturdy and feels like you get what you pay for. I wish it had integrated clips, but a lot of sinks still don't. I also wish the drain came ready for a disposal. I like the edges of the sink that go over the counter top. They are thick and creates a luxury look. This product meets my expectations and is much better quality than the comparable Ruvati that I bought first and returned.

Scritto da: Stefan

Really nice sink

Looks great and fits the largest pots we have.

Scritto da: BRG

Missing Part

This sink did not come with the drain housing and locknut assembly required to attach to plumbing. My contractor had to purchase this part separately. My different brand of kitchen sink I purchased earlier came with this part.

Scritto da: Amazon Customer

Amazing quality for the price.

This is a beautiful sink. After months of use it's handled it well with little scratches

Scritto da: Richard S

Really nice robust sink.

I bought this sink to replace an under mount sink in our island unit. The worktop is quartz so needed to be cut to take the install. I used a Dewalt wetsaw with a diamond blade. Things to note: The template for marking out is super accurate and the hole needs to be right on the line. Not inside or you will need to cut more. I found that with the whole clips attached the sink was too tight to ease into place, so I split the clips and slid the “hook” part up into place after the sink was in position. The lip around the outer edge of the sink is fairly deep so the best seal is to use a preformed sealing strip. Applying a thick bed of silicone to the underside before placing is certain to end with silicone all over the place. It is worth fixing the facet before setting the sink as it is a lot easier to tighten the fixing nut. There is a second hole in case a soap dispenser etc. Is to be installed. The blanking plug is best sealed on the underside of the sink rather tha around its top edge. We have had our sink for a couple of weeks now and really like it

Scritto da: Kevin

Nice big sink. Wish I had it years ago!

I was looking for a sink exactly like this one. I got lucky and found an Amazon Warehouse deal with a big discount. The sink is exactly what I wanted. Just barely fit in my counter/cupboard so that made installation a little harder, but still not to bad. Measure and cut the bike carefully. I had to trim the hole a second time to make it bigger. I suggest testing the size by cutting a hole in the bottom of the box it came in to ensure it fits. I think their provided template may be a little too small.