Kohler K-GP77005-RP Keramikventil, Einheitsgröße, raue Platte

Name: Kohler K-GP77005-RP Keramikventil, Einheitsgröße, raue Platte
Brand: Kohler
SKU: 0650531630469
Price: 38.69 EUR
Availability: InStock

Brand:Kohler

3.8/5

€
38.69

Kohler ECHTES Teil. Ventile müssen durch das gleiche Ventil ersetzt werden, ein Upgrade auf Ultra Glide ist nicht möglich. Für die meisten KOHLER-Wasserhähne mit zwei Griffen von 1990 bis 2010. Keramikscheibe sorgt für Haltbarkeit und lang anhaltende Leistung. Keramikventil um eine Vierteldrehung drehen, im Uhrzeigersinn schließen. Schützen Sie KOHLER-Produkte und achten Sie immer auf das KOHLER GENUINE PARTS-Logo.

Menge

in den Warenkorb legen Kaufe jetzt

EAN: 0650531630469

Kategorien Werkzeuge & Heimwerken, Grobinstallation, Hahnteile, Kartuschen,

Brand	Kohler
Certification	Kohler Valve
Item Dimensions LxWxH	2.25 x 1 x 0.75 inches
Material	Ceramic

5 Star

4 Star

3 Star

2 Star

1 Star

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet^*

Deine Bewertung

Scritto da: SnowmanXT

WELL

Easy to remove depends totally on who you followed. Hulk installed the one I had to remove so removal didn't really go well. I gave 5 stars anyway because the sink is still there without signs of a struggle. Easy to install. It went well but you do have to watch which way they turn to shut the water off and which side Hulk put the Hot water valve on. Overall the value was great and it all went well.

Scritto da: Tap500

Trust Kohler parts

Easy to install. Less than 10 minutes and no more leaking faucets. Flow seemed to increase after changing as well. Lots of YouTube videos on changing these out of you have never done one.

Scritto da: Azulza

Exact replacement for Kohler Forté Sink Facuets

Perfect replacement for the Kohler (K-R10273-4N-BN) Forté Sink Faucets. The old ones are damn near impossible to remove due to 12 years of hard water calcification but once you can actually remove them these are an easy install. Finger tight + quarter turn makes it leak proof. At $14/each this makes a $28 faucet like new again, rather than buying a $130 new set. They're still in good condition, and this seems to be the only moving part which seizes up, so I'm hopeful that these will be good for another decade. Also, just to make it complicated, Kohler likes to list both this brass valve along with the ceramic updated version in the same document, so make sure you look closely at the one you have and buy the CW and CCW versions. This wasn't clear to me and I ended up buying one set of each which resulted in my returning the wrong set. No biggie, it all worked out in the end. P.S> There are a LOT of videos on YouTube showing how to replace these. There are a few good ones, watch those before you go off on your own for the first time.

Scritto da: jijimba

Perfect

Great quality

Scritto da: LJB

Works great - install may call for some additional 'oomph' - DeWalt to the rescue

The valve works great and it's a perfect fit. However, removing the old ones can be difficult, if not close to impossible, with normal hand tools. The problem is that the entire valve body rotates and you run the risk of breaking the feed lines etc... I have seen several folks recommending removal of the entire valve from the cabinet to get this out. Didn't want to do that so I broke out my DeWalt 20V impact gun with a 13MM deep socket. Grabbed the threaded portion of the valve under the cabinet to hold it steady and with a few short bursts these came out with no drama. This saved me a ton of time and effort. Putting the new ones in just use your normal wrench and don't over tighten them. I put a bit of plumbers grease on the threads in the hopes this will make it easier for the next person doing this job, should that be needed.

Scritto da: Smart Shopper

Best value!

PERFECT REPLACEMENT!

Scritto da: D. Mayberry

Got the job done!

The valve on our bath became stuck on about a year and a half ago. I panicked and broke the handle and was able to get the water off. I didn't have the knowledge to fix it myself at the time or the funds to hire someone, so the tub sat since then. I finally watched some YouTube videos for tub repair and took on the task of fixing the tub myself. Once all the parts came in, it only took about a total of an hour labor tops, and just over $100 to make the repairs myself.

Scritto da: penguingrooves

Perfect for replacing my old faucet's leaky valve on the hot side.

This was to replace the hot water valve for Kohler faucet K454-4S-CP. It was a perfect match AND included the black spline to be used at the top for attaching the stem extender (87466). My faucet was crusted over badly, and it took some PB B'laster penetrant and time to loosen the gunk. I was too feeble to remove it with a ratchet wrench and needed a stronger person. Thankfully, the old valve was removed. If you're not able to remove the valve cartridge, you'll have to buy a different model's valve and casing assembly (Ultraglide). Hopefully, you'll be as lucky as me and can preserve the old parts. I could not remove the old stem extender for two handles, and another handle had an ill-fitting stem extender. So, i bought new stem extenders to go with the new valves. If you mistakenly bought the wrong side's valve, you can modify it by removing the clip and changing the orientation. Good luck with fixing your leaky faucet.

Scritto da: bceric

Correct part for the purpose

Good price and fast delivery; part worked well.

Scritto da: Alex

Perfeft

Correct valves were sent and easily replaced!

Scritto da: John O Dale

Great prompt service.

The replacement cartridge works as it should.

Scritto da: Domenico Corsetti

Good product

Exactly as described, pay attention to the “close” direction as there are 2 different part numbers for “hot” and “cold” levers.

Scritto da: Amazon Customer

Worked like a charm...

Item was delivered quickly and worked awesome. Replaced the part on my 20+ year old Kohlbert faucet. Saved me buying a new faucet prior to me completing my bathroom Reno....