IVY Classic 45364 1 Zoll x 3/16 Zoll Sechskant-Einsatz-Bit, Impact Plus, 10er-Pack. 1 x 3/16 Sechskant-Bit, 10er-Pack

Brand:IVY Classic

3.6/5

28.57

Länge: 1 Zoll, Größe: 3/16 Zoll Sechskant, Schaft: 1/4 Zoll Sechskant. Präzisionsgefertigt für ideale Passform und hervorragende Haltekraft. Wärmebehandelt und angelassen auf Rockwell-Härte 60–62, sandgestrahlte Oberfläche verhindert Rost. Entwickelt, um dem hohen Drehmoment (Rotationskraft) von Schlagschraubern standzuhalten, Impact Plus (eingetragenes Warenzeichen). Hochwertiger S-2-Werkzeugstahl für zusätzliche Festigkeit und Haltbarkeit.

Keine Einheiten verfügbar
Länge: 1 Zoll, Größe: 3/16 Zoll Sechskant, Schaft: 1/4 Zoll Sechskant. Präzisionsgefertigt für ideale Passform und hervorragende Haltekraft. Wärmebehandelt und angelassen auf Rockwell-Härte 60–62, sandgestrahlte Oberfläche verhindert Rost. Entwickelt, um dem hohen Drehmoment (Rotationskraft) von Schlagschraubern standzuhalten, Impact Plus (eingetragenes Warenzeichen). Hochwertiger S-2-Werkzeugstahl für zusätzliche Festigkeit und Haltbarkeit.
Brand IVY Classic
Drive System External Hex
Item Dimensions LxWxH 1 x 0.25 x 0.25 inches
Material Alloy Steel
Size 1" x 3/16" Hex Bit

3.6

9 Review
5 Star
74
4 Star
14
3 Star
7
2 Star
2
1 Star
4

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet*

Scritto da: Amazon Customer
If you’re a grip, get these.
I’m a grip in the film industry and needed these for my speed wrench. These fit the Cal Van finger drives and work just fine. I used loctite (superglue) to keep it from falling out of the finger drive.
Scritto da: Operator
Bulk at a decent price.
I lose 3/16 bits all the time, and 10 for $15 is way better than going to a hardware store to buy a multi-bit kit in different sizes for the same price.
Scritto da: G-wiz
Are these a bit small? or Is it just me?
The bolts to my VW Passat engine intake are a little odd, I guess. I've been using 5mm, but I noticed that only 1 5mm bit fits. I noticed that it's 3/16. "Great. These fit better." But I get some more because I keep dropping them. These are very sloppy. OK, so all these are Chinese made. Everything is Chinese made and I have no problem with that. However, to really properly assess these, I think I need to bring my calipers out the next time and measure all my 5mm and 3/16 bits and figure out what the heck is going on here. I AM sure those bolts are 3/16. These bits are too loose. Of all the 3/16 bits I have, these are the smallest, and could cause a problem. They're so loose that if they were any smaller, they'd just turn in the bolt head under pressure and possibly get stuck or break the head. Beyond this, I'll need to measure them and compare with all my old Allen wrenches. I have some old, made in USA ones, I'll compare with those. I'll revise this when that happens. My current verdict is that these are too small. More like 4mm.
Scritto da: Adam
Mostly good but very hard.
Got these for my job of checking screw tightness. The fit is looser than I would like but the steel held up well. Got through about 3500 screws before I had to chuck it. The loose fit caused the little wear it had to be enough to start slipping in the screw. It the fit were a bit tighter it would be an absolute fantastic bit. Update: after working with them for a couple months I downgraded to 3 stars. The bit is very hard, therefore very brittle. I have snapped so many of these it is kinda sad. Metal doesn't deform which is good but they snap decently easy with a t handle bit holder.
Scritto da: Timothy Bergstrom
Perfect. - Its good to have lots of quality bits.
I use these for Grip work. These are good quality.
Scritto da: Allan
Good quality, well made 1/8" bit drive
Great for what it is. A good quality 1/8" bit that does the job well. Fits well with no "slop" when under pressure. Good price too.
Scritto da: BENJAMIN D ZUCKER
Item does not match the picture.
I ordered this because it looked more durable than other brands. But after I received it, they look different. Not what I was expecting.
Scritto da: Dave
It works
It’s just a basic bit. It work great for my use
Scritto da: Enrico Gagnon
Correct
Bon pour le prix

Verwandte Produkte

hot
hot
CTA Tools 9574 Torx-Bit – T90
4/5

€ 52.54

CTA Tools 9574 Torx-Bit – T90
4/5

€ 52.54

hot
Wera 05059605001 840/4 Z-Bits, 3 x 50 mm
0.1/5

€ 72.01

Wera 05059605001 840/4 Z-Bits, 3 x 50 mm
0.1/5

€ 72.01

Entdecken Sie unser internationales Netzwerk

Wir versenden in 28 Länder, über 200.000 Produkte. Bleiben Sie auf dem Laufenden, abonnieren Sie den Newsletter.

Array