Calculated Industries 7445 AccuMASTER Duo Pro stift- und stiftloser Feuchtigkeitsmesser erkennt versteckte Lecks und Feuchtigkeit

Name: Calculated Industries 7445 AccuMASTER Duo Pro stift- und stiftloser Feuchtigkeitsmesser erkennt versteckte Lecks und Feuchtigkeit
Brand: Calculated Industries
SKU: 0098584003128
Price: 106.70 EUR
Availability: InStock

Brand:Calculated Industries

3.5/5

€
106.70

Das 7445 AccuMASTER Duo Pro Pin & Pinless Modisture Meter ist ideal für die Messung des Feuchtigkeitsgehalts in Hartholz, Schnittholz, Holzböden, Ziegeln, Beton, Trockenbauwänden und Putz. Sein Dual-Sensor-System kann Ihnen dabei helfen, Ihre Feuchtigkeitserkennung mithilfe von PA oder Stiften zu beschleunigen und zu verbessern. Es ist das Beste aus beiden Welten.HOLZBEARBEITER UND HANDWERKER – können die Stifte verwenden, um den Feuchtigkeitsgehalt in Prozent schnell und einfach zu überprüfen, bevor sie Bauholz und Harthölzer kaufen oder verwenden. PROFI- UND HEIMWERKER-UMMODELLER & FLIPPER – Entdecken Sie versteckte Wasserschäden in Böden, Wänden und darunter Teppiche aufgrund von Dachlecks, Überschwemmungen, Rohrbrüchen, unterirdischem Versickern oder anderen Wasserquellen. Wenn Sie einen hohen Feuchtigkeitsgehalt lokalisieren, können Sie erkennen, wo Reparaturen durchgeführt werden müssen, um weitere Schäden zu vermeiden und toxische Wucherungen oder andere Gesundheitsrisiken zu stoppen. SIE KÖNNEN LEICHT SEHEN – Dank des großen, gut gestalteten LCD-Displays und der ständig eingeschalteten Hintergrundbeleuchtung von AccuMASTER können Sie problemlos sehen Lesen Sie es auf schlecht beleuchteten Baustellen, auf Holzplätzen, in Werkstätten oder sogar nachts auf Ihrem Holzstapel. Darüber hinaus können Sie mit der Hold-Funktion einen Messwert auf dem Display einfrieren, um ihn aus einem bequemeren Blickwinkel betrachten zu können. Benutzerfreundlich und einfach zu verstehen – Drücken Sie im Pin-Modus die (austauschbaren) scharfen Edelstahlstifte fest in das Testmaterial. Oder platzieren Sie im Pad-Modus die Rückseite des Messgeräts auf der Oberfläche, auf der Sie nach Feuchtigkeit suchen möchten. Die gut lesbaren Ziffern und klar gestalteten Symbole zeigen Ihnen sofort an, ob der Feuchtigkeitsgehalt hoch, mittel oder niedrig ist. Darüber hinaus gibt es optionale akustische Alarme, sodass Sie den Füllstand auch dann hören können, wenn Sie sich in einer dunklen oder ungünstigen Umgebung befinden, in der Sie den Bildschirm nicht sehen können. Dank der robusten, handfreundlichen Form und den seitlichen Gummigriffen können Sie Messungen bequem durchführen. ALLES, WAS SIE ZUM ARBEITEN BENÖTIGEN – Das robuste AccuMASTER XT Feuchtigkeitsmessgerät bietet Genauigkeit und benutzerfreundliche Funktionen. Enthält eine 9-Volt-Batterie und batteriesparende automatische Abschaltung (3 Minuten). Stellen Sie sicher, dass Ihr Holz oder Baumaterial einsatzbereit ist – klicken Sie jetzt auf „In den Warenkorb hinzufügen“! Copyright 2021 Calculated Industries. Alle Rechte vorbehalten.

Menge

in den Warenkorb legen Kaufe jetzt

EAN: 0098584003128

Kategorien Werkzeuge & Heimwerken, Mess- & Layoutwerkzeuge, Scanner & Prüfgeräte, Feuchtemessgeräte,

EINFACHE BEDIENUNG – Großes, gut lesbares Display mit Hintergrundbeleuchtung. Der robuste, handfreundliche Testerkörper fühlt sich stabil an, wenn austauschbare Stifte in Materialien gedrückt werden. Halten Sie die Taste gedrückt, um den Lesevorgang einzufrieren. Testen Sie Holz oder poröse Baumaterialien – Trockenbau, Teppich, Ziegel, Beton und Putz. PRÜFEN SIE BAUHOLZ UND HARTHOLZ VOR DEM BAU UND DER HOLZBEARBEITUNG – Verwenden Sie die Stifte, um den Feuchtigkeitsgehalt Ihres Holzes zu ermitteln, um sicherzustellen, dass Sie für Ihre Projekte kein feuchtes, feuchtes Holz verwenden, um Risse, Spalten und Verformungen zu vermeiden. Stellen Sie vor der Verlegung sicher, dass sich der Holzboden akklimatisiert hat. PERFEKT FÜR HAUSINSPEKTIONEN – Verwenden Sie das Pad für schnelles, nicht-invasives Scannen ohne Stift, um Orte mit überdurchschnittlich hoher Feuchtigkeit hinter einer Wand oder unter einem Boden zu finden. VORSICHT: Der leistungsstarke, stiftlose Pad-Sensor misst bis zu ¾ Zoll, kann jedoch durch Materialien beeinflusst werden, die bis zu 2 Zoll unter dem Objektmaterial liegen (z. B. Metallschrauben, Nägel, Werkbankstützen usw.). Halten Sie Ihre Finger vom Pad-Scanbereich fern. Verwenden Sie das Pad, um Abweichungen vom Normalzustand zu erkennen, und verwenden Sie Stifte, um diese zu quantifizieren. SCHÄTZEN SIE DEN FEUCHTIGKEITSGEHALT SCHNELL UND EINFACH – der Detektor bietet die ideale Doppelfunktion von stift- und stiftlosen Sensoren in einem. Verwenden Sie das stiftlose Pad als schnelle „Entfernungs“-Funktion, um einen großen Bereich nach verdächtigen Bereichen abzusuchen, ohne Löcher zu hinterlassen. Wechseln Sie dann zu Stiften, um den Feuchtigkeitsgehalt in verschiedenen Tiefen zu quantifizieren.

Batteries	‎1 9V batteries required.
Batteries Included?	‎Yes
Batteries Required?	‎Yes
Battery Cell Type	‎Alkaline
Brand	Calculated Industries
Country of Origin	‎China
Customer Reviews	4.5 4.5 out of 5 stars 1,946 ratings 4.5 out of 5 stars
Included Components	‎One AccuMaster Duo Pro Moisture Meter with a protective cap, 9V battery, User's Guide, 1-year warranty
Item Dimensions LxWxH	6 x 2.5 x 1 inches
Item model number	‎7445
Item Package Quantity	‎1
Item Weight	‎8.1 ounces
Manufacturer	‎Calculated Industries
Mounting Type	Surface Mount, Wall Mount
Mounting Type	‎Surface Mount, Wall Mount
Part Number	‎7445
Pattern	‎Sensors
Power Source	‎Battery Powered
Product Dimensions	‎6 x 2.5 x 1 inches
Style	‎Dual Pin+Pinless, Backlit LCD
Usage	‎Outside; Professional, Inside; Amateur, Inside; Professional, Outside; Amateur
Voltage	9 Volts
Voltage	‎9 Volts
Warranty Description	‎One year warranty

5 Star

4 Star

3 Star

2 Star

1 Star

Schreiben Sie eine Bewertung

Ihre E-Mail wird nicht veröffentlicht. Alle Pflichtfelder sind mit gekennzeichnet^*

Deine Bewertung

Scritto da: Alex Bentley

Both pin and pad modes work consistently

I’ve used this on a variety of materials in the various modes and I’ve gotten consistent and reasonable values each time. Certainly not the cheapest unit, but I’m willing to spend a bit more on a decent product. I’ve tried it on sheet goods, construction lumber, firewood, hardwoods, and the like. I used the right mode for each type of material. When using the pin mode I didn’t jam it in, but used enough pressure to make good contact, each time aligning the pins with the grain. I even used the pad mode on some older furniture indoors and got what I would have expected. Wood i’ve had in my shop for some time also got good results. If you are looking for a moderately priced unit that works reliably, this just might be it.

Scritto da: Gary Bouchard

It works as I expected it would.

It works as I expected it would.

Scritto da: Carla

Awesome product

This gas helped me in my jibs to proof humidity

Scritto da: Bridgette Lylyk

Great purchase

Easy to use and read. Great purchase.

Scritto da: Peter D.

Pinless mode surface-sensitive and reproducible for log-ends if held flat

For hardwoods, I haven't had much luck inserting the pins into my firewood (the pins bend) so I use the pinless mode. By hovering the meter over my (other) palm, the sensing pad just beings to read above zero at around half an inch separation, increasing to 100% when in contact with my (other) palm. For split firewood, I can get very reproducible readings if the sensing pad is flat, in direct contact with the log end (which requires the log end to be flat), and if I place the pad in roughly the same location on the end. To hold the meter flat to the wood surface, I grip astride the display rather than by the red bumpers, so most of the time I listen for the rate of the chirps. The readings are plausible based on how easily the logs burn, with the caveat that the wood needs to be seasoned enough that the moisture content within half an inch or so of the flat surface that the pad is measuring is representative of the log. The end could also be unrepresentively wetter than the middle if it was recently rained on or otherwise subject to high humidity. I suppose I might choose which stack to draw from next based upon log-end measurements in the piles, then if I had concerns, cut a log in half so that I could get a measurement the center for confirmation. For firewood stored outside for airtight stoves in humid climates, the range of interest for water content is (say) 10 to 30 percent. It would be helpful if the chirps' rate, slow-to-rapid, could apply to a smaller range of readings to allow the user to better discriminate without consulting the display. This could perhaps be achieved (say) by using pitch to indicate range and rate to indicate the reading within that range. Inside the house, the logs continue drying for a time, so the meter is helpful choosing which logs and how many to bring in (perhaps fewer logs need grace the living room than if logs are chosen at random). When it comes to fueling the stove, the meter is helpful to choose which logs to pull next from the rack. Checking of the ends, and heft relative to the log size, serve to confirm the choice.

Scritto da: edward johnson

Really happy that I ordered this!

We recently had a pipe burst in our crawl space. Since we don't ever go into the crawl space, we didn't discover it until I noticed water on the hardwood floors in the powder room. I don't know how long it had been spewing hot water.. I called a plumber to fix the leak, and then a restoration company to remove all of the soaked insulation, etc. Some of the hardwoods were cupped or buckled, and I noticed that the contractors used a tool to measure moisture levels all around the affected areas. I thought it was a good thing to be able to check moisture levels around our home, so I decided to see if I could find a similar tool on Amazon. I found the Accumaster Duo Pro. I didn't know if it was the same model they had used, but it looked just like it, so I ordered it. I think it arrived the next day, which was yesterday (Friday). My husband works out of town during the week and returns home each weekend and I was excited to show him the new tool I had ordered. We were scheduled to make a 6 hour drive to buy a previously owned boat today, and he thought we should bring this tool. We are so thankful that we did. The condition of the boat wasn't as good as advertised, but the definitive factor in our decision that it wouldn't be a wise investment was the moisture that this tool detected in the transom. We checked it on different surfaces to assure ourselves that the readings were accurate - and it seemed that they were. It was worth the purchase for that alone, but now we have a tool that we plan to use to keep on top of moisture and mold problems in our home and our kids' homes, too. We hope that we will use it reguarly and that it continues to be as useful as it was today for a long time to come!

Scritto da: theo

Device did the job.

Pretty accurate and made with quality.

Scritto da: George A Pollard

It is very accurate

Moisture content of timber

Scritto da: Marey M.

Sensor Pad innaccurate

This seemed to be a great product, but I was not aware at first that the sensor pad was defective. When an engineer did readings around my window with his own meter he pointed out the sensor pad readings on the AccuMaster were wildly inaccurate. If the moisture were really 80% – 99%, the drywall would have to be dripping wet. Readings with pins seem to be fine. It was too late to do a return through Amazon so I contacted the company, but ultimately they couldn't do anything to fix it. UPDATE: The vendor, Calculated Industries, sent me a replacement meter so have revised my rating from 1 star to 4. I have to take 1 star off as the customer service was somewhat lacking. I had originally exchanged 15 emails over 2 months and then heard nothing more. I even asked about a warranty. I then contacted Amazon customer service who referred me back to the company again, as the window for a return was closed, but there is a 1-year warranty. It was only after a formal letter to Calculated Industries that I was mailed a replacement. I was skeptical that it could just be anther dud, but the difference in readings with the senor pad was dramatic. So, finally, I have what appears to be a fine product.

Scritto da: rockromantic

Pin and Pad readings are useful in combination

The Pin and Pad readings on timber were pretty much as I would have expected. So I'd say they were useful & reliable particularly if the question was is it ok for painting or flooring or will it indicate a water/moisture problem. the thinner pins allow you to push the meter into the wood further than stubby pins. The Pin reading for brick/concrete is useful for a surface reading. The Pad reading takes some getting used to as it is a "relative" reading and tends to be highish (that's normal), eg. on brick that I regarded as slightly cool to the touch but ok for painting or rendering I recorded 60 - 75%. Above 75% it may be better to wait for a hot/dry day for painting/rendering. 80+ is probably reasonable to say the material is a bit moist but then you need to determine if it is coming from inside or is it just absorbed from outside after rain.

Scritto da: MB

If you have a water leak, the AccuMAsTER will find it!

We could smell that there was an occasional musty smell coming from our fully finished basement. Try as we might, we couldn't find any evidence of a leak. We decided to order the AccuMASTER. Within minutes of receiving the meter, we were able to test moisture readings throughout the basement and quickly isolated the problem. Once we knew where the leak was, it was easy to fix (and no ripping out the whole basement to find it). While I am not 100% sure that the readings are accurate, they are directional correct and will certainly identify if/where you have a problem; and the meter is very easy to use and to read.

Scritto da: D smith

Found humidity in my basement

This machine worked great. I found the high humidity in the basement. I’m so happy of this purchase. I found it by using the pinless technique. Worth it. I didn’t have to hire someone to tell me where the problem is, saved a loooot of $$$.